If you are on a well, an outage is not an inconvenience, it is a water outage. No showers, no laundry, no dishes, and after one flush each, no toilets. That changes the calculation from comfort to necessity.
What a well pump actually draws
| Pump size | Running watts | Starting surge | Typical use |
|---|---|---|---|
| 1/2 HP | ~1,000 W | ~2,500 W | shallow well, small home |
| 3/4 HP | ~1,500 W | ~3,500 W | common residential |
| 1 HP | ~2,000 W | ~4,500 W | common residential |
| 1.5 HP | ~2,800 W | ~6,000 W | deeper well |
| 2 HP | ~3,800 W | ~8,000 W | deep well or high demand |
Notice the surge column. A 1 HP pump runs on 2,000 watts but demands more than double that for the second or two it takes to start. Submersible pumps are direct-start motors under load — they are pushing a column of water — and that inrush is what matters for generator sizing.
The problem is that it starts when it wants to
You cannot schedule a well pump. It starts whenever the pressure tank drops below its cut-in point — which may be the exact moment the air conditioner compressor also kicks in.
That coincidence is what sizes the generator. You need headroom for the largest surge plus whatever is already running, not just the sum of the running watts.
What we recommend
| Your situation | Size | Why |
|---|---|---|
| Essential circuits, well + furnace + fridge | 10–14 kW | the cheapest route to keeping water on |
| Whole house, gas heat, 1 HP pump, 3-ton AC | 22 kW | room for pump and compressor together |
| Whole house, 1.5–2 HP pump | 24–26 kW | bigger surge needs more headroom |
| Electric water heater as well | 26 kW | add 4,500 W continuous |
Essential circuits is a strong option here
A well is a textbook case for essential-circuits backup. Pump, furnace, refrigerator, a few lights and outlets gets you water, heat and food for a fraction of whole-house cost — and water is the thing you actually cannot do without.
Three things people forget
- The pressure tank helps you. A properly sized tank means the pump runs less often, which reduces how frequently that surge lands on the generator.
- Septic may need power too. If you have a pump-up septic system or a sewage ejector, that is another motor with another surge. Count it.
- Water heaters still need water. Backing up an electric water heater is pointless if the pump that fills it is not also on the generator.
Wiring the pump circuit
Well pump circuits are motor circuits and are sized from the nameplate — typically 12 AWG for 1/2 to 1 HP and 10 AWG above, but the pump or control box data plate governs. Long runs to a well house frequently need a size up for voltage drop; see wire size for a 100 foot run.
Square footage is a starting point, not an answer. Run the sizing calculator — it works from your actual loads and sizes against the fuel you run — or send us the details and a licensed electrician will check it.
Frequently Asked Questions
What size generator do I need to run a well pump?
For the pump alone, a 10kW unit is comfortable for pumps up to 1 HP. For whole-house backup including a well pump and air conditioning, 22kW to 26kW depending on pump size — the starting surge is what sets it.
Will a 10kW generator run a well pump?
Yes for most residential pumps up to about 1 HP, which draw roughly 2,000 watts running and 4,500 watts at start. That leaves room for a furnace and refrigerator on an essential-circuits system.
Why does a well pump need so much starting power?
A submersible pump starts under load, pushing a column of water. That inrush is roughly double its running draw and lasts a second or two, and it can arrive at the same moment your air conditioner starts.
