Generac 9953 200-Amp Automatic Transfer Switch with Type 2 SPD
200A automatic transfer switch. Not service-rated — installs downstream of your existing main.
Generac 200A automatic transfer switch. Not service-entrance rated — installs downstream of your existing main disconnect. Includes a Type 2 surge protective device. It monitors the utility feed, signals the generator to start when power drops, transfers the load across, and returns it when the grid is back.
Why You Cannot Skip the Transfer Switch
A transfer switch is not an accessory. It is the device that makes generator power legal and safe, and it does one essential thing: it guarantees your house is never connected to the generator and the utility at the same time.
Without it, generator power flows backwards out of your house and onto the utility line. That line is being worked on by someone who has confirmed it is dead. Your generator re-energises it, and the step-up through the pole transformer turns 240 volts into several thousand. Backfeeding kills linemen. It is also illegal everywhere in the United States, it will fail inspection, and it voids your homeowner’s insurance.
NEC 702.5 requires the transfer equipment. There is no version of this job that skips it.
Service-Rated or Not? This Is the Decision
More orders go wrong on this point than on amperage, so it is worth being precise.
| Service-entrance rated | Contains a main breaker and can act as the service disconnect. It replaces your main, sitting between the meter and the panel. Fewer boxes on the wall, usually less conduit, and often a cleaner install on a retrofit. |
|---|---|
| Not service-rated | No main disconnect inside. It must be installed downstream of an existing main. Cheaper, and the right answer when you already have a perfectly good service disconnect you are keeping. |
Which you need depends on your existing service, not on preference. If your meter feeds a main breaker panel and that panel is staying, a non-service-rated switch downstream is usually correct. If you are replacing the service equipment, or the meter feeds the panel directly with no separate disconnect, you need the service-rated version.
Your inspector will check this. Send us a photo of your meter and panel and we will tell you which one you need before you buy the wrong box.
This unit is not service-entrance rated. It has no main disconnect inside, so it must be installed downstream of your existing main. If your meter feeds a main breaker panel and that panel is staying put, this is normally the correct and cheaper choice. If you have no separate service disconnect, you need the service-rated version instead — we stock those too.
Size It to the Service, Not the Generator
The amperage on a transfer switch matches your electrical service, not your generator’s output. A 200 amp service takes a 200 amp switch, whether the generator behind it is 14kW or 26kW.
Look at the main breaker in your panel. That number — 100, 150, 200, 400 — is the number you need. Getting this wrong in either direction is a problem: undersized is a code violation and a hazard, oversized is money spent for nothing.
What Automatic Actually Buys You
A manual switch does the same electrical job for far less money. The difference is that someone has to be home to throw it. Automatic is what keeps the freezer cold and the sump pump running when the outage starts while you are at work or asleep.
You will also need conductors between the generator and the switch, and that sizing has its own rule — NEC 445.13 requires 115% of nameplate current, which is not the figure in the ordinary ampacity table. Read what size wire you need before the trench is open, and see our THHN/THWN-2 building wire.
Specifications
| Manufacturer part | 9953 |
|---|---|
| Brand | Generac |
| Rating | 200A |
| Voltage | 120/240 V single phase |
| Type | Automatic transfer switch |
| Service-entrance rated | No — install downstream of an existing main |
| Installed by | Licensed electrician — permit and inspection required in most jurisdictions |
| Genuine OEM | Yes |
Compatibility depends on your generator’s controller generation. Tell us your generator model and we will confirm the pairing.
Why Buy From ZapDaddy Supplies
- Licensed electricians answer the phone — send us a photo of your panel and we will confirm the switch before you order
- Generator, switch and wire ship together so the installer has the whole job on site
- Straight answers on code — we will tell you what your inspector is going to ask
Ready to Order?
Add it to the cart to see your price. If you are at all unsure whether you need the service-rated version, call first — it is a far cheaper conversation than a returned switch.
| Attributes | Value |
|---|---|
| Brand | |
| Amperage |
200A |
| Voltage |
120/240V |
| Phase |
Single Phase |
Complete the job
-
Briggs & Stratton 40786 22,000-Watt Dual Fuel Home Standby Generator
$6,280.00Add to cart for lowest price -
Generac 7260 22 kW Home Standby Generator — Dual Fuel
$6,309.00Add to cart for lowest price -
Generac 7328 26kW Home Standby Generator with 200A service-rated ATS
$8,219.00Add to cart for lowest price
Compare similar models
-
Generac 6333 60A Manual Transfer Switch
$160.00Add to cart for lowest price -
Reliance 306LRK 30-Amp ProTran 2 Manual Transfer Switch
$310.00Add to cart for lowest price -
Reliance 510C 50-Amp Manual Transfer Switch
$405.00Add to cart for lowest price -
Generac RXSC100A3 100A Automatic Transfer Switch
$415.00Add to cart for lowest price -
Generac 6854 30-Amp HomeLink Manual Transfer Switch
$440.00Add to cart for lowest price -
Generac 9854 50A Manual Transfer Switch
$515.00Add to cart for lowest price -
Generac RXG16EZA3 100A Automatic Transfer Switch — 16 Circuit (Service Rated)
$545.00Add to cart for lowest price -
Generac 9947 100A Automatic Transfer Switch
$620.00Add to cart for lowest price














